Show
This preview shows page 6 - 9 out of 12 pages. 29. A network administrator is troubleshooting router RA in an EIGRP autonomous system. Theadministrator needs to obtain the IP addresses of the router with which router RA has establishedadjacencies. It is also important to obtain information of the queue counts on the neighbor routers.What command will do this?Show cdp neighbor detailsShow ip eigrp interfacesShow ip eigrp topology all-linksShow ip eigrp neighbors 30.An administrator wants to replace the configuration file on a Cisco router by loading a newconfiguration file from a TFTP server. What two thing does the administrator need to know beforeperforming this task? (Choose two.) Get answer to your question and much more 32. What two encryption algorithms are used in IPsec VPNs? (Choose two.) AES3DESPSKDHIKE33.FE80:1FF02:1FFO2:52001:DBA:ACAD:135.)The command ipv6 unicast-routing has not been implementedThe ip address is missing on interface Gigabit Ethernet 0/0The router ID has not been created on router 1The EIGRP process has not been activated on interface G0/0 Get answer to your question and much more 37.Which task has to be performed on Router 1 for it to establish an OSPF adjacency with router 2? Get answer to your question and much more 38. Why are users in the OSPF network not able to access the Internet?The OSPF timers that are configured on routers RI, R2, and R3 are not compatible.The OSPF network statements are misconfigured on routers R2 and R3.The network statement is misconfigured on router R1.The interfaces that is connected to the ISP router is down.The default route is not redistributed correctly from R1 by OSPF 39. A network administrator has just changed the router ID on a router that is working in an OSPFv2environment. What should the administrator do to reset the adjacencies and use the new router ID? Get answer to your question and much more Upload your study docs or become a Course Hero member to access this document Upload your study docs or become a Course Hero member to access this document End of preview. Want to read all 12 pages? Upload your study docs or become a Course Hero member to access this document Tags IP address, Router, Router ID CCNA (ICND2) Cert Practice Exam1.On which switch interface would an administrator configure an IP address so that the switch can be managed remotely?oFastEthernet0/1oVLAN 1ovty 0oconsole 02.Which two issues might cause excessive runt and giant frames in an Ethernet network? (Choose two.) Get answer to your question and much more 3.Refer to the exhibit. Match the packets with their destination IP address to the exiting interfaces on the router. (Not alltargets are used.)CCNA ICND2 024CCNA (ICND2) Cert Practice Exam 001 4.Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.Which task has to be performed on Router 1 for it to establish an OSPF adjacency with Router 2? Get answer to your question and much more 5.Refer to the exhibit. A network administrator is reviewing port and VLAN assignments on switch S2 and notices thatinterfaces Gi0/1 and Gi0/2 are not included in the output. Why would the interfaces be missing from the output? Get answer to your question and much more oThey are administratively shut down.oThey are configured as trunk interfaces.6.Which address type is not supported in IPv6?oprivateomulticastounicastobroadcast7.Which feature on a Cisco router permits the forwarding of traffic for which there is no specific route? Get answer to your question and much more 8.A network administrator is using the router-on-a-stick model to configure a switch and a router for inter-VLAN routing. Whatconfiguration should be made on the switch port that connects to the router? Get answer to your question and much more 9. 9. QuestioRefer to the exhibit. A ping to PC3 is issued from PC0, PC1, and PC2 in this exact order. Which MAC addresses will becontained in the S1 MAC address table that is associated with the Fa0/1 port?10.A network administrator is designing an IPv4 addressing scheme and requires these subnets. Get answer to your question and much more 1 subnet of 100 hosts2 subnets of 80 hosts2 subnets of 30 hosts4 subnets of 20 hostsWhich combination of subnets and masks will provide the best addressing plan for these requirements? o9 subnets of 126 hosts with a 255.255.255.128 masko3 subnets of 126 hosts with a 255.255.255.128 mask6 subnets of 30 hosts with a 255.255.255.224 masko3 subnets of 126 hosts with a 255.255.255.192 mask Upload your study docs or become a Course Hero member to access this document Upload your study docs or become a Course Hero member to access this document End of preview. Want to read all 34 pages? Upload your study docs or become a Course Hero member to access this document Tags IP address, administrator What will an OSPF router prefer to use first as a router ID*?What will an OSPF router prefer to use first as a router-id? The first preference for an OSPF router ID is an explicitly configured 32-bit address. This address is not included in the routing table and is not defined by the network command.
Which three OSPF states are involved when two routers are forming an adjacency choose three?The Down, Init, and Two-way states are involved in the phase of neighboring router adjacency establishment.
Which step does an OSPF enabled router take immediately after establishing an adjacency with another router?Exchange link-state advertisements. Build the topology table. Execute the SPF algorithm.
Which command will verify that a router that is running ospfv3 has formed an adjacency with other routers in its OSPF area?The show ip ospf neighbor command is used to verify that the router has formed an adjacency with its neighboring routers.
|
Which task has to be performed on router 1 for it to establish an OSPF adjacency with router 2 Remove the passive interface command from interface FastEthernet 0 0?
zusammenhängende Posts
Urheberrechte © © 2024 ketiadaan Inc.
