Show
Submitted: October 23rd, 2020 Reviewed: January 5th, 2021 Published: January 28th, 2021 DOI: 10.5772/intechopen.95835 AbstractThe central composite design is the most commonly used fractional factorial design used in the response surface model. In this design, the center points are augmented with a group of axial points called star points. With this design, quickly first-order and second-order terms can be estimated. In this book chapter, different types of central composite design and their significance in various experimental design were clearly explained. Nevertheless, a calculation based on alpha (α) determination and axial points were clearly described. This book chapter also amalgamates recently incepted central composite design models in various experimental conditions. Finally, one case study was also discussed to understand the actual inside of the central composite design. Keywords
*Address all correspondence to: 1. IntroductionAny optimization process is achieving by going through certain phases, i.e., Screening; where identification of significant and important factor is important [1]; Improvement; where factors need to be identified which is near to optimum, Response surface design [2]; where optimum or best product has been designing by response surface method (RSM) by quantifying the relationship between one or more measured responses and vital input factor [3]. It is always been a tedious tasks to choice a suitable experimental design, which can easily explain many response variables. Such variables often end as quadratic surface model. For such kind of interpretation central composite design can be an excellent choice. In the process of Optimization and finding the best possible product from the ongoing batches, an experimental design called the central composite design (CCD) concept has emerged [4]. The CCDmodel is an integral part of response surface mythology. The biggest advantage of this type of optimization model is, it is more accurate, and no need for a three-level factorial experiment for building a second-order quadratic model [5]. After excising the CCDmodel within the experiment, a linear regression model has been used to construct the model, and coadded values have been used [6]. The CCDmodel is otherwise called A Box-Wilson Central Composite Design. In this design, the center points are eventually augmented with the group of “star points” that allows estimation of curvature [7]. If the distance from the center of the design space to a factorial point is ±1 unit for each factor, the distance from the center of the design space to a star point is ± α with ׀α׀ > 1 [8]. The precise value of α depends on certain specific properties required for the design. Since there are many factors available in the CCD model, therefore, the possibility of more than two or many star points within the model is more palpable. The star points represent lower and higher extreme values. The CCD model allows to extends 2 level factors, which have been widely used in response surface modeling and Optimization. As far as pharmaceutical research is a concerned, much scientific research has been carried out in recent times in this direction. As per Krishna Veni et al(2020), environment-sensitive Eudragit coated solid lipid nanoparticles can be prepared using a central composite design (CCD) model [9]. In another study, Ye, Qingzhuo, et al.(2020) prepared puerarin nanostructured lipid carriers by central composite design, where 5 levels 3 factors central composite design was used to utilized to anticipate response variables and to constrats 3D plots [10]. However, in this book chapter, an attempt was made to highlight the basics of the CCD model and to corelate the concepts of CCD with suitable case studies, which could increase the readers’ inquisitiveness. Advertisement 2. Essential steps in responses surface methodology
2.1 Models of the model used in the optimization processThe first-order model for the Optimization can be depicted as: For quadratic or second-order model, if nonlinearity was reported, then the following equation was incorporated: Y=β o+β1X1+β2X2+β12 X1X2+β11X12+β22X22+ϵ E2 The factor must be very at level three while activating to fit the second-order model [16]. It was observed that, during the dictation of center point and two-level design, the quadratic terms can be identified, but it cannot be adequately estimated [17]. In Figure 1, the condition at which the Optimization can occur was explained, i.e., Optimization can be confirmed when second order model can be optioned from statistical outcomes and which coincide with the optimum value. During the factorial design experiment, it is preferable to avoid three-level designs as chances of an increase in the number of runs would be more [16]. Figure 1.Optimization condition. For CCDDesign and Box–Behnken Design, second-order models are widely used. The analyzing aspect of these two designs can be explained by the following equation: Y= bo+b1X1+….+bkXk+b12X1X2+b13X1X3+…+bk−1,kXk−1 Xk+b11X12+…+b kkXk2+ϵ E3 The above equation represents the quadratic model, which is near to the Optimization. In this equation, Y = Dependent variables or Outcome variables or estimated responses, X1 = independent variables, b0 = overall mean response or intercept constant, b1 = regression model coefficients, K = number of independent variables, ϵ = error. Put into words, a mathematical model to the observed values of the dependent variables y, that indicates:
Based on the outcomes and empirical models from various experimental design, the central composite design gives us a direction to logically think and exercised multivariable analysis [18]. Three design points are prerequisite to establishing a second-order polynomial equation in CCDmodel [19]. When two levels of fractional factorial design need to be established, then 2k should have possible +1 and − 1 levels of factors. In similar patterns, 2 k needs to be calculated, which can be otherwise called star points, and α forms the center to generate quadratic terms. The center point of the CCD., the model, provides an excellent independent estimation of experimental error. Where N is the actual number of experiments, n is a number of repetition and k is the number of different factors which were incorporated within the study. Eventually, the CCD model can be best explained by the design of an expert (Version 11.0) software. The various steps involved in central composite design (CCD) was discussed in Figure 2. Figure 2.Central composite design flow diagram. To determine the local axial point, it is necessary to identify the alpha value in the CCD model. Depending on the alpha vale design can face cantered, rotatable, orthogonal. The alpha value can be calculated using the following equation: If α value comes equals 1, the position of axial points stands within the factorial region. This is otherwise called a face-centered design, with three levels of factors that need to be kept in the design matrix. To calculate and analyze experimental results from response surface methodology, a polynomial equation needs to be implemented to study the correlation between dependent and independent variables. Y=β+β1X1+β2X2+β 12X1X2+β11X12+β22 X22+E E5 Advertisement 3. Types of central composite designThe Box and Wilson design or CCD model comprising of factorial1, factorial2, and factorial3 design [20]. The star point outside the domine and the center point, representing the experimental domine, helps determine the response surface plot [21]. By estimating the precision of surface responses, the value of α can be determined; where star design is ± α. There are three types of CCD; the α can be determined according to the calculation possibilities and the required precision, which can be obtained from surface responses. The α value’s positioning determines the quality of the design or estimation. The rate by design is identified by determining the position of the points [22]. The precision of the estimation influence by the number of trials at the center of the domine. The quality by design approach is necessary to estimate the coefficients’ variability and responses [23]. One key aspect is rotatability or iso-variance per-rotation, which means that the prediction error is identical from all the points to the center points from the same distance [24]. Eventually, the center composite design was classified into three types: 3.1 Circumscribed design (CCC)In central composite design, the levels of the factors eventually stand on the edge. The CCD model (Figure 3) is always magnate with corner points, which was represented in red dots. From the center point (blue), the extract points are constrained from the sides (green dots). In this CCD model, each factor would have 5 levels. The star points are establishing new extremes for the low and high settings for all factors. These designs having circular, spherical or hyperspherical symmetry and required 5 levels for each factor. Supplementing an already existing factor or factorial design with a start point can produce the design. The Circumscribed (CCC) was found to be a rotatable design [25]. Figure 3.CCDmodel. 3.2 Inscribed design (CCI)When the limit is specified for factor settings, the CCI design utilized the factor setting as star points and created a factorial design within those limits [26, 27]. In other words, CCI design is a modified version of CCC design, where CCC design has been divided by α to generate the CCI model. Eventually, CCC and CCI were found to be a rotational model (Figure 4). Figure 4.Comparison of the three types of central composite designs. 3.3 Face cantered (CCF)In this design, for each face of the factorial space, star points are the center point. Therefore. α = ±1. This variable requires 3 levels of each factor [28]. The face cantered designs (CCF) are a non-rotatable design (Figure 4). In Figure 4, with two factors, three types of center composite design are used. From this design, one thing is clearly evidenced that; CCI explores the smallest process space, and CCC enjoys the largest process space. The CCC models looking like a sphere rotates around the factorial cube. Advertisement 4. The parts of box and Wilson composite design4.1 Determination of α valueAlpha (α) value can be defined as the calculated distance of each individual axial point (star point) from the center in the center composite design [29]. If Alpha (α) is less than 1, which indicates the axial point must be a cube, and if it is greater than 1, it indicates it is outside the cube. In central composite design, each factor has five levels, i.e., Extreme high or otherwise called a star point, higher point, center point, low point, and finally, extreme low star point. Figures 5 and 6 describe how to select the total number of experimental runs for the CCD model as well as how to design two factors factorial design (Table 1).Coming to the Alpha (α) determination; which can be determined by the following equation: Figure 5.(A) Parts of CCD (B) Total number of experimental runs required in the CCDmodel; where K = number of variables and r = fraction of full factorial. Thus, two-factor central composite design, the number of experimental runs is; 22 + 2(2) +1 = 9. Figure 6.Schematic presentation of two-factor central composite design.
Table 1.Number of factors and α value. α = (Number of factorial runs)1/4. = (2k or 2k−r) ¼. If K (number of factors) =2. Alpha (α) = (22)1/4 = 22/4 = 21/2 = 1.414. 4.2 Uncoded value value of alpha (α)To determine the uncoded value α value, the following equation can be used: uncoded value value = (Coated value x L) + C; Where, L = Length expressed in real units between centre points and + 1 value of factor and C = Centre point value expressed in real units. For temperature: Uncoded value of – α = (Coded value × L) + C. = (−1.414 × 30) + 60 = 17.58. Uncoded vale of + α = (Coded value× L) + C = (1.414 × 30) + 60 = 102.42 (Table 2).
Table 2.α value of one experiment. Advertisement 5. Advantages of center composite design
Table 3.Design matrix for 2 factors central composite design [30].
Table 4.Design matrix for three factors central composite design [31]. Advertisement 6. Limitation of central composite design
Same examples of CCDoptimization in recent experimental conditions are mentioned in Table 5.
Table 5.Examples of CC demployed for the optimization. Advertisement 7. Case study-1As per S. Bhattacharya., (2020) studies [41] varius independent variables viz., entrapment efficacy percentage, zeta potential, particle size, percentage of calmative drug release of a polymeric nanoparticle formulation was evaluated and optimized using central composite design (CCD); which was interpreted by Design Expert (Stat-Ease; version 11.0) software. Upon considering the alpha point at 1.68179, in this 21 baches experimental design, 4 factors, and 2 levels were considered (Table 6). Based on the optimization surface plot batch with desired particle size, zeta potential, cumulative drug release (%) entrapment efficacy (%) were selected for further characterization studies. Table 7 indicating critical quality attributes and necessary process attributes that affect the outcomes of the nanoparticles. By using polynomial equations and a 3-dimensional surface plot, the effects of critical process parameters on essential attributes of quality were examined Figure 7.
Table 6.Critical process parameters that influence various critical quality attributes.
Table 7.Desired construction of critical quality attributes. Figure 7.(A-D) represents the surface plot identifying the effects of critical process parameters on essential attributes of quality. From this CCDmodel, the following polynomial equations can be derived: Particle Sizenm =236.054−101.38A−3.6663B−8.85986C+0.594604D−40.7804AB −24.375AC−16.375AD+2.625BC−30.2549BD−18.375CD+45.2505A2+1.23307B2+11.1326C2+0.879517D2 E6 Zeta PotentialmV=−21.8583+ 1.11191A−0.772985B−0.19847C+6.18685D−1.42565AB+0.77AC−0.242985AD −1.0125BC+0.829409BD+0.385CD−0.644786A2−1.44735B 2−0.805653C2+1.23081D2 E7 Cumulative drug release%at80thhours =75.2947+2.52409A−1.66192B+2.1758C−17.5081D+2.73315AB −0.65625AC−0.605667AD+0.71625BC+2.56284BD−0.4687CD+0.534547A 2−1.0918B2−1.11301C2−5.01271D2 E8 Entrapment efficacy%=53.323+0.184327A+ 3.54978B+2.29125C+14.0832D+5.83819AB+1.2475AC+1.6522AD +3.1875BC−4.10817BD−3.25CD+2.30194A2+0.088697B2 +1.78045C2−0.192378D2 E9 By considering A as homogenization speed, B as homogenization time, C as surfacetant concentration (%) and D as polymeric concentration; respectively, the polynomial Eqs. 6, 7, 8, & 9 can be interpreted. From these polynomial equations, critical process parameters of qualifiable effects on essential attributes can be determined. It can easily predict from the polynomial Eq. 6, that particle size of the polymeric nanoparticles can be increased, when homogenization time & speed and surfactant concentration decrease. The elevated negative co-efficient in homogenization speed of polynomial Eq. 6, indicates it has a significant influence on particle size. Higher shearing stress during elevated homogenization time & speed could lead to mass transfer between the particles, ultimately resulting in nucleation and smaller particle size. From Eq. 7, it can be predict that homogenization time & surfactant concentration has antagonistic effects on zeta potential and homogenization speed has an agonistic effect on zeta potential. In a similar fashion equation 8, shows homogenization speed & surfactant concentration has an agonistic effect on cumulative drug release (%) at 80th hours. From Eq. 9 it was clear that entrapment efficacy (%) increases with increases of homogenization speed, homogenization time & surfactant concentration. Advertisement 8. Case study 2As per Jaleh Varshosaz et al. (2010) [42] research, amikacin solid lipid nanoparticles can be prepared by using a central composite design. In this research, central composite design (CCD) was utilized to identify a suitable formula with minimum particle size; where, three independent variables were considered, i.e., the ratio of drug to lipid (A), amount of lipid phase (B), the volume of aqueous phase (D). The alpha value of the experiment was found to be −1.682; the alpha value helps in determining rotatability and orthogonality within this design. In this experiment, a total of 20 experimental designs have been incepted, along with 8 factorial points and 6 axial points were considered. The best-fitted model can be assumed after quadratic model analysis by ANOVA and F-value determination. From the Figure 8(II&III) it was clarly evident that, decrease concentration of drug to lipid ratio, aquous phase valume whould certlay decrease particle size; which indicates agonistic effects on particle size, where else, from the Figure 8(IV), it was evident that, increase concentration of cholesterol would increases the drug loading capacity. Therfore, by resolving all the polynomial equation obtained from Figure 8graph, it was identified that, at 0.5 drugs to lipid ratio, 314 mg cholesterol, 229 mL of aqueous phase an optimized formulation would possibly be constructed with lower particle size and higher drug loading efficacy (%). Therefore, At these levels of independent variables, predicted amikacin particle size and loading efficiency were calculated to be 153 nm and 86%. Figure 8.(I)Normal probability plot for broadcast, the most critical variables are influencing the particle size. The ratio of drug to lipid (a), surfactant type (B), amount of lipid phase (C), and volume of aqueous phase (D).(II)the effect of drug-to-lipid ratio (a) and amount of cholesterol (C) on particle size.(III)the effect of drug-to-lipid ratio (a) aqueous-phase volume (D) on particle size.(IV)the impact of aqueous-phase volume (D) and the amount of cholesterol (C) on loading efficacy(%). Advertisement 9. ConclusionThis book chapter’s main agenda was to enlighten the present approaches and recent optimization research activities based on the CCD model, as specially for pharmaceutical product development. The CCDmodel is useful for modeling and analyzing programs in which the response of interest influences several variables. The CCDmodel can be considered as a robust statistical tool for process optimization. The best part of CCDis, as compared to Plackett–Burman design, a limited number of experiments are required with less computational experience. The biggest challenge of the CCDmodel is finding the critical factor. Central composite designs are beneficial in sequential experiments because you can often build on previous factorial experiments by adding axial and center points. Advertisement AcknowledgmentsThe author is like to acknowledge the help and motivation of Dr. R.S. Gaud, Director, SVKM’s NMIMS. Deemed-to-be University, Shirpur Campus, for providing excellent research facilities and profound inspiration while drafting this book chapter. The author is also like to acknowledge his own original research publication entitled “Fabrication and characterization of chitosan-based polymeric nanoparticles of Imatinib for colorectal cancer targeting application”; for taking inputs from that article while drafting this book chapter. Conflict of interestThe author declares that the author has no competing interests. References
Written By Sankha Bhattacharya Submitted: October 23rd, 2020 Reviewed: January 5th, 2021 Published: January 28th, 2021 © 2021 The Author(s). Licensee IntechOpen. This chapter is distributed under the terms of the Creative Commons Attribution 3.0 License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. How many independent variables are in a 2x2x2 factorial design?A 2×2 factorial design is a type of experimental design that allows researchers to understand the effects of two independent variables (each with two levels) on a single dependent variable.
How many potential two way interactions are there in a 2 2 2 factorial design?Let's take the case of 2x2 designs. There will always be the possibility of two main effects and one interaction.
How many conditions and possible interactions are there in a study with a 2 2 2 factorial design?This would be a 2 × 2 × 2 factorial design and would have eight conditions. Figure 8.2 shows one way to represent this design. In practice, it is unusual for there to be more than three independent variables with more than two or three levels each.
What is a 3x4 factorial design?In this notation, the number of numbers tells you how many factors there are and the number values tell you how many levels. If I said I had a 3 x 4 factorial design, you would know that I had 2 factors and that one factor had 3 levels while the other had 4.
|